The Synthesis of Sulfated Titanium Oxide Nanotubes

TiO₂ nanotubes can be prepared in gram quantities by treating anatase TiO₂ powder with concentrated NaOH solution. These TiO₂ nanotubes acquired strong acidity after being impregnated with sulfuric acid solution and calcined at 300 °C. The anatase TiO₂ powder used to prepare the nanotube did not catalyze the esterification between cyclohexanol and acetic acid, while sulfated TiO₂ nanotubes were very reactive toward the esterification reaction.     

光漂白法制备有机聚合物非线性定向耦合器

研究了用光漂白的方法制备PMMA/DR1聚合物非线性定向耦合器,提出了一种容易的制备方法来得到要求的耦合长度.测量了材料的光学非线性对定向耦合器两臂透过率的影响.实验结果表明由于光学非线性,耦合器的耦合长度随着入射光强度的改变而发生变化.     

用膜电解法处理低浓度SO2吸收液的三室电解槽材料的选择

提出了用膜电解法处理低浓度SO2吸收液的方法，介绍了三室电解槽的设计原理及在电场作用下，电解槽内离子的迁移和电解反应机理，系统地讨论了电解槽组成单元材料（如阳离子交换器）的选择及在H2SO4－NaHSO3-Na2SO3体系中金属阳极的选择等，并进行了试验验证，得到了很好的结果。     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

掺杂VO2的特性、制备方法及应用

VO2在68℃时发生从低温的单斜相向高温四方相转变，同时伴随着光、电、磁性能的突变。通过掺入其它杂质元素，能有效改变其相变温度和光、电性能，这些优异特性使其具有更好的应用前案。本文综述了掺杂的原理，掺杂对VO2相变影响、常用的掺杂方法及目前的应用情况，这对其进一步的研发应用具有重要的意义。     

钛铜复合棒及其标准化

概述了钛铜复合棒研制开发及发展历程,并介绍了钛铜复合棒的主要性能,以及钛铜复合棒的标准化情况。     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

CO2泡沫压裂优化设计技术及应用

针对苏里格低压、低渗透气藏常规水基压裂液压后返排困难,导致储层水锁伤害的问题,研究利用CO2泡沫压裂来降低压裂液滤失,提高压裂液返排率,降低对储层的伤害。有针对性地研究了CO2泡沫压裂优化设计技术,包括:CO2泡沫压裂起泡技术、酸性交联技术、变泡沫质量和恒定内相设计技术等。现场应用表明,长庆苏里格气田气藏应用CO2泡沫压裂技术,可大大提高返排率,缩短压裂液返排时间,降低压裂液对气层的伤害,提高压裂效果。     

基体温度对磁控溅射沉积ZAO薄膜性能的影响

利用中频交流磁控溅射方法 ,采用氧化锌铝陶瓷靶材 [w(ZnO) =98%、w(Al2 O3 ) =2 % ]制备了ZAO(ZnO∶Al)薄膜 ,观察了基体温度对ZAO薄膜的晶体结构、电学和光学性能的影响 ,采用X射线衍射仪对薄膜的结构进行了分析 ,采用光学分度计和电阻测试仪测量了薄膜的光学、电学特性 ,采用霍尔测试仪测量了薄膜的载流子浓度和霍尔迁移率。结果表明 :沉积薄膜时的基体温度对薄膜的结构、结晶状况、可见光透射率以及导电性有较大的影响。当基体温度为 2 5 0℃ ,Ar分压为 0 8Pa时 ,薄膜的最低电阻率为 4 6× 10 -4Ω·cm ,方块电阻为 35Ω时 ,可见光 (λ =5 5 0nm)透射率高达 92 0 %。